Reese 44601 PROFESSIONAL RECEIVER Bedienungsanleitung PDF herunterladen

Installation Instructions

Dodge Journey

Part Numbers:

75648

87487

44601

Hitch Shown In Proper Position

Equipment Required: Lubricant or Soapy water , Tape

Wrenches: 3/4”

1. Lower muffler and tailpipe by removing all rubber isolators, behind rear axle. There will be (2) or (3) depending on vehicle.

Be careful not to allow mufflers to fall under their own weight. Note: Spraying a lubricant or soapy water on the metal hanger

rod and the rubber isolator helps removal.

2. Feed spacers and carriage bolts into impact bar using the pull wires provided (both rail). Leave pull wire attached.

3. Tape spacers in place to hitch before raising hitch into position. Orient spacer as shown. See Figure 2.

4. Raise hitch into position, taking care not to push carriage bolts back into impact bar. Secure with conical washers and nuts.

Single exhaust -Raise hitch on the passenger side over exhaust pipe and slowly rotate hitch into position.

Dual exhaust - Slide hitch above tailpipes.

5. Bend and insert handle nuts thru access holes in frame and install two (2) 1/2”-13 bolts and conical washers as shown.

6. Tighten all fasteners to the required torque specification. Caution: Hold handle nuts in place to prevent them from rotating.

Bend end out of the way

7. Raise exhaust back into position and reattach to rubber isolators. NOTE: If additional exhaust clearance is required, bend

exhaust hanger bracket, which is welded to vehicle frame, downward.

z 2013 Cequent Towing Products – Printed in Mexico

Sheet 1 of 3 75648N 3-1-13 Rev. B

Qty. (2) Carriage bolt 1/2-13 X 2.25 GR5

Qty. (2) Hex nut 1/2-13

Qty. (2) Spacer

Qty. (2) Hex bolt 1/2-13 X 1.50 GR5

Qty. (4) Bevel spacer

Qty. (2) Handle nut

Qty. (4) Conical washer

Qty. (2) Pull wire

Tighten 1/2-13 carriage bolts with torque wrench to 75 Lb.-Ft. (102 N*M)

Tighten 1/2-13 Handle nuts with torque wrench to 50 Lb.-Ft. (68 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

Fastener Kit: 75648F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

4000 (1816 Kg) 400 (182 Kg)

Weight Carrying

Ball Mount

4000 (1816 Kg) 400 (182 Kg)

Wiring Access Location: SUV 1, 2

Form: F205 Rev A 5-6-05

Fascia

Frame

rail

Note: Fasteners

typical both sides

Single exhaust shown for clarity

Figure 1.

Impact

bar

Hitch

bracket

Impact bar

Orient spacers as shown.

HINT: Tape spacers in

place to hitch before

raising hitch into position

Figure 2.

Rearward

1 2 3

Dodge Journey 1

Inhaltsverzeichnis

Seite 1 - Dodge Journey

Installation Instructions Dodge Journey Part Numbers: 75648 87487 44601 Hitch Shown In Proper Position Equipment Required: Lubricant or Soapy water ,

Seite 2

Instructions d’installation Numéros de pièces : Attelage montré dans la position appropriée Équipement requis : Lubrifiant ou eau savonneuse, R

Seite 3

j k l mn q mo Larguero del bastidor l Única muestra de gases de escape de claridad Figura 1. p Barra de impacto Instrucciones de instalación Números d

Kommentare zu diesen Handbüchern

Keine Kommentare

Reese 44601 PROFESSIONAL RECEIVER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Reese 44601 PROFESSIONAL RECEIVER herunter. Reese 44601 PROFESSIONAL RECEIVER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Reese 44601 PROFESSIONAL RECEIVER