Reese 44641 PROFESSIONAL RECEIVER Bedienungsanleitung PDF herunterladen

Installation Instructions

Ford Edge Sport

Part Numbers:

75686

87576

44641

Hitch Shown In Proper Position

Equipment Required: ½” Pull wire (Provided), Tin Snips

Wrenches: 3/4”, 5.5mm, 8mm

Ford Edge

Fascia

Figure 1

1. Lower exhaust system at the (3) rear rubber isolators.

2. Disconnect the fascia center support (1 screw) and carefully push it toward the impact bar and out of the way. Reinstall screw.

3. Remove both heat shields (3 screws) and a plastic insert each side.

4. Trim both heat shields as shown. Figure 2.

5. Using the kink wire (see Figure 3) method for feeding fasteners attach carriage bolt and block to the pull wire. Feed forward

fasteners into place on both rails using the access hole at the end of the frame rail. On the outside end of both rails there is a

wide notch to make this process easier. Feed rearward fasteners into location using the same method. Note: Make sure

spacer are sitting flat on the rails and not on existing weld nuts.

6. Replace trimmed heat shields using the remaining inboard fasteners and plastic insert.

7. Raise hitch into position over the exhaust. Sandwiching the heat shield between the hitch and the rail.

8. Loosely attach fasteners as shown, center hitch on vehicle and tighten fastener to 75 Lb.-Ft. (102 N*M).

9. Raise exhaust system (3) places back into position.

Rev. A1-11-1075686NSheet 1 of 3

z 2010 Cequent Performance Products

Spacer ¼ X 1 X 3Qty. (4)

Conical Washer Qty. (4)

Hex Nut ½-13Qty. (4)

Carriage Bolt ½-13 X 1.500 GR5Qty. (4)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75686F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Wiring Access Location: SUV1 & SUV2

Form: F205 Rev A 5-6-05

Rail

Figure 2

Figure 3

Trim both heat shields.

As shown

Kink Pull wire to keep spacer

independent of bolt

Frame rail

Access hole at end

of rails

Rubber isolator

Trim both heat shields.

Leave enough to sandwich

between frame and hitch

Forward

hole

350 (159 Kg)3500 (1589 Kg)

Weight Carrying

Ball Mount

Not For Use With Spring Bars

Weight Distributing

Max Tongue

WT (LB)

Max Gross

Trailer WT (LB)

Hitch type

Fasteners typical both sides.

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsFord Edge SportPart Numbers:75686 87576 44641 Hitch Shown In Proper PositionEquipment Required: ½” Pull wire

Seite 2 - Instructions d’installation

Instructions d’installationFord Edge SportNuméros de pièces :Attelage montré dans la position appropriéeÉquipement requis : Fil de tirage ½” (fourni)

Seite 3 - Instrucciones de instalación

Instrucciones de instalaciónFord Edge SportNúmeros de partes:El enganche se muestra en la posición correctaEquipo necesario: Cable de halar de 1/2” (

Kommentare zu diesen Handbüchern

Keine Kommentare

Reese 44641 PROFESSIONAL RECEIVER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Reese 44641 PROFESSIONAL RECEIVER herunter. Reese 44641 PROFESSIONAL RECEIVER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Reese 44641 PROFESSIONAL RECEIVER